-
What Are the Basic Load Cases in CAESAR II?
Most students enjoy the first hour of CAESAR II. You draw some pipe, drop in a few supports, type in the diameter and wall thickness, and the screen starts to look like a real piping system. Then someone says “now set up your load cases” and the room goes quiet.
This happen as the names look like code and you have no idea how they will be used. So here in this article we have made this easier for you. If you are looking to understand this in detail, then applying for the Caesar 2 Training can be beneficial for you. This training help you learn the basics from the scratch.
A pipe is under several forces at once. It has its own weight, the fluid inside, the pressure pushing outward, and the heat making it grow. A load case is just you telling the software which of those forces to apply together, and then asking whether the pipe is okay.
You do this because the forces don’t always show up together. A pipe sitting cold and empty is in a different situation from the same pipe running hot and full. You want to check each situation separately.
The loads you’ll see
in the list– W is weight. It covers the pipe, the fluid and any insulation.
– P1 is the internal pressure.
– T1 is the operating temperature.
– WIND is wind load on the pipe.
– U1 is a uniform load along the pipe, often used for earthquake loads.
– D1 is a displacement, like when a pump nozzle moves because the pump heats up.
– F1 is a point force, such as the kick from a relief valve.
You pick from these when you build each case.
The First Three Cases to Learn
This is weight plus pressure, with no temperature. These loads are always there, so the code puts a strict limit on the stress they can cause. If this one fails, the usual reason is a long unsupported span that sags. Adding a support or moving one closer normally fixes it.
Now the pipe is running for real, hot and under pressure. This case is where you read displacements and support loads. It tells you how far the line moves and whether it bumps into a steel beam or the pipe next to it. It’s also what you use for the loads going onto equipment.
This one trips people up because you don’t build it from raw loads. It’s the operating case minus the sustained case. What’s left is the effect of heat alone. CAESAR II usually labels it something like L3 = L2 – L1. The code gives expansion stress its own limit, because pipes relax a bit after they’ve moved. If expansion fails, your pipe is too stiff, and you can fix that by adding a bend or a loop to give it room.
Wind and earthquake don’t happen every day, but the pipe still has to survive them. So you build an occasional case by adding the extra load on top of sustained, something like W + P1 + WIND. Codes let you use a higher allowable stress here, since the load is short-lived. In ASME B31.3, for example, the limit goes up by a third. Check your own code and edition, though, because this changes from one to the next.
Before a plant starts up, the pipes get filled with water and tested at high pressure. Water is much heavier than steam or gas, so a line that looks fine in normal service can be overloaded during the test. You set up a separate case with the weight of the water and the test pressure. Beginners often forget this one, and then a spring hanger ends up in trouble on site.
Let the software help, but don’t
switch offThere’s a Recommend button in CAESAR II that suggests basic load cases after you enter your loads. Use it. It saves time and it’s a good way to see how a normal set looks.
But read what it gives you. If you’ve added wind or seismic loads, make sure they actually appear in a case. A wind load you entered but never used does nothing, and the software won’t complain.
You will learn when you build a small model, break this and fix the same. So applying for the Caesar ii Certification training will give you the chance to work on the real layouts to work on. Also you can show the certification to your employer.
Stress analysis stays in right next to the design. So number of engineers are applying for the the SP3D Course. It will help you understand how the 3D layout gets made before this reach the stress team. It can help lot while you need to ask the designer for moving a line.
If you are still confused, just start with sustained, operating and expansion. Once you read and understand these three results without any panic, rest including the wind, seismic and hydro test, is the same idea with a different load added.
-
This discussion was modified 3 weeks ago by
professional it-training.
-
This discussion was modified 3 weeks ago by
professional it-training.
-
This discussion was modified 3 weeks ago by
Sorry, there were no replies found.